This paper describes a very simple and reliable procedure for measuring shape and deformation of electronic components with a single experimental set-up. The procedure is based on two electronic speckle pattern interferometry (ESPI) techniques referred to as conventional ESPI and phase shifting ESPI (PS-ESPI). The present research is motivated by the fact that mismatch in thermal expansion coefficients of the different materials included in electronic packaging (EP) may cause mechanical failures since thermal stresses will change sharply through subsequent loading cycles. ESPI is particularly suitable for measurements on EP since it allows us to perform non–contact testing of non-planar heterogeneous surfaces. It is apparent that gathering detailed topographic information will certainly help us to measure accurately surface deformations of EP along with modeling correctly numerical analysis. As is known, the accuracy of results obtained with ESPI may be significantly improved by phase shifting techniques (PST). Therefore, this paper compares the relative merits of different phase-stepping strategies in order to find which strategy will perform the best for the optical set-up utilized in the experiments. Preliminary investigations on a standard specimen under three-point-bending served to choose properly the optical set-up and phase-stepping procedure which yield the best fringe visibility. Four-phases achieved the best fringe visibility and the minimum number of invalid pixels.These information have been utilized in the experimental campaign on standard and surface mounted technology (SMT) electronic components. ESPI and PS-ESPI have been used for analyzing the transient state and the steady state of devices, respectively. From the experimental results obtained here, it appears possible to measure strains induced by thermal loading cycles. The experimental set-up, based on the Lendeertz’s interferometer, proved itself also able to contour specimen surface at a good level of detail. Remarkably, by using the same set-up for deformation and shape measurements we can preserve the pixel by pixel relationship between displacements and surface depth which will hold true if correlation between different exposures is not destroyed. The results obtained in this research justify using PS-ESPI in order to understand better failure mechanisms of electronic components. This fact along with the exact knowledge of object shape may be particularly useful in the different design stages (including FEM modeling and analysis) of electronics for special applications.

A comprehensive ESPI based system for combined measurement of shape and deformation of electronic components

GENOVESE, KATIA;
2004-01-01

Abstract

This paper describes a very simple and reliable procedure for measuring shape and deformation of electronic components with a single experimental set-up. The procedure is based on two electronic speckle pattern interferometry (ESPI) techniques referred to as conventional ESPI and phase shifting ESPI (PS-ESPI). The present research is motivated by the fact that mismatch in thermal expansion coefficients of the different materials included in electronic packaging (EP) may cause mechanical failures since thermal stresses will change sharply through subsequent loading cycles. ESPI is particularly suitable for measurements on EP since it allows us to perform non–contact testing of non-planar heterogeneous surfaces. It is apparent that gathering detailed topographic information will certainly help us to measure accurately surface deformations of EP along with modeling correctly numerical analysis. As is known, the accuracy of results obtained with ESPI may be significantly improved by phase shifting techniques (PST). Therefore, this paper compares the relative merits of different phase-stepping strategies in order to find which strategy will perform the best for the optical set-up utilized in the experiments. Preliminary investigations on a standard specimen under three-point-bending served to choose properly the optical set-up and phase-stepping procedure which yield the best fringe visibility. Four-phases achieved the best fringe visibility and the minimum number of invalid pixels.These information have been utilized in the experimental campaign on standard and surface mounted technology (SMT) electronic components. ESPI and PS-ESPI have been used for analyzing the transient state and the steady state of devices, respectively. From the experimental results obtained here, it appears possible to measure strains induced by thermal loading cycles. The experimental set-up, based on the Lendeertz’s interferometer, proved itself also able to contour specimen surface at a good level of detail. Remarkably, by using the same set-up for deformation and shape measurements we can preserve the pixel by pixel relationship between displacements and surface depth which will hold true if correlation between different exposures is not destroyed. The results obtained in this research justify using PS-ESPI in order to understand better failure mechanisms of electronic components. This fact along with the exact knowledge of object shape may be particularly useful in the different design stages (including FEM modeling and analysis) of electronics for special applications.
2004
File in questo prodotto:
Non ci sono file associati a questo prodotto.

I documenti in IRIS sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.

Utilizza questo identificativo per citare o creare un link a questo documento: https://hdl.handle.net/11563/8482
Citazioni
  • ???jsp.display-item.citation.pmc??? ND
  • Scopus 25
  • ???jsp.display-item.citation.isi??? 20
social impact